Remove old grout with oscillating machine

Remove old grout with suitable machine will help you save labor and cost. TKT Cleaning will share with you about one kind of machine could help you remove old grout with less effort, more efficient.

1. Remove old grout with oscillating machine instruction

Step 1: Scrape out stubborn chunks of grout with oscillating machine.

Fit the oscillating tool with a blade specially intended for tile or tile grout. Most tool heads will specify which materials they can be used for (metal, wood, tile, etc.).

Start by holding the tool horizontally (or vertically, in the case of vertical seams), turning on the power, and lightly pressing the blade to the grout.

Let the power tool do the work; do not force it. The blade should easily chew through the grout.

Once you have removed as much grout as possible by holding the tool horizontally, it is time to gently angle the blade to remove more grout.

Once again, working slowly and patiently will help ensure that you do not damage the edges of your tile.

One trick is to support your arm on a tool box so that it does not get tired during the process.

After you have done as much grout removal as possible with the power tool, your next line of attack is the small flat-head screwdriver.

Its head will fit into the seam and allow you to scrape out stubborn chunks of grout.

Do not try to remove every last bit; that is for the next step. Your intent is to knock out hunks that the oscillating tool may have loosened but not completely removed.

oscillating machine for removing old grout

Image: oscillating machine for removing old grout

Step 2: Switch To Utility Knife To Remove Grout

Switch To Utility Knife To Remove Grout

If you are still finding bits of grout that will not come out, switch to your dull-bladed utility knife.

You want a dull blade for two reasons.

First, it makes no sense to kill a nice, sharp blade on tile grout. Use that sharp blade for something else first.

Second, you do not want to risk snapping off the sharp point of the utility knife and getting injured.

Continually Vacuum Grout Work During and After

Remove Tile Grout

Be sure to liberally use the shop vacuum during the grout removal process so you can see what you are doing.

And of course, you will want to use it once again at the end to clean up your work site.

Oscillating machine blade tkt cleaning

Image: Oscillating machine blade tkt cleaning

2. Evaluation of oscillating machine with reciprocating saw and blade

It works effectively on the floor or wall and comes with a little risk of damaging the tile.

However, the blade of this tool is thin and may require the combination of several blades to remove all the grout.

It also requires that you buy or have a reciprocating saw.

Our Pick: Grout Grabber GG001 – Grout Removal Tool for Reciprocating Saws

Grout Grabber Grout Removal Tool for Reciprocating Saws

If you already own a reciprocating saw, you should consider adding the Grout Grabber GG001 to your collection for a quick and accurate grout removal.

This 6-inch Grout Rake features a curved cutting edge (2-inch blade) for optimum grout removing accuracy.

It has coarse carbide grit that helps in the removal of all cement-based and epoxy grout types from 1/16 inch to 1/2 inch.

You even can use this to make a relief cut that to remove a chipped or cracked tile.


  • Effective grout removal tool from any joint size
  • Handy
  • Produces a minimum amount of dust while removing grout
  • Can be used by hand, without the saw on hard to reach areas


  • The blade wears out quickly
  • The blade is a bit costly

TKT Cleaning would like to share you some knowledge about machine and tool to remove old grout. If you are looking for an efficient tool to remove grout without chipping the tiles, the Grout Grabber might be the best way to go. It can also be used when replacing tile grout.

How to remove old grout with very simple tools


In this article we will instruct you how to remove old grout without expensive tools. You can remove old grout with very very simple tools you can see around your house.

When remodeling a bathroom or kitchen, the hardest part can be removing the grout from pre-existing tile. Grout is made from water, cement and sand, which hardens over time to form a rock-like material. The strength of grout is what makes tile so highly desired, as it prevents the tile from shifting. Learning how to remove grout can save you a lot of money that you would otherwise have to pay to a contractor.

1. Preparing Before Remove old grout

Get the necessary tools. There are a number of tools which you can use to remove the grout. Those you choose will depend on how much money you wish to spend, how much and which type of grout you need to remove, and how often you intend to remove grout.

You can use power tools. There are a variety of tools, called grout removal tools or re-grout tools, which will help you remove grout quickly and with much less effort. These are helpful if you have a large amount of grout to remove or remove grout often.

You can use manual tools as well. If you for some reason cannot use power tools but find that you have a reasonable amount of grout to remove, use a manual grout removal tool. This will look like a small trowel.

If you only have a small amount of grout to remove or it is something soft like rubber grout, you can use a standard razor blade, like an exacto knife or a utility knife.

Image: simple tool to remove old grout

2. Tapering

If you are planning to keep the tiles and removing just the grout, cover the edges of each tile with painter’s tape.

Cover the surfaces of the appliances you are planning to keep. As the grout is removed, flying debris can cause damage. Drape a large blanket or drop cloth over the appliances, making sure they are fully covered.

If necessary, use tape to secure the edges of the protective covering and make sure to cover drains completely.

3. Don protective clothing

Don protective clothing before starting the grout removal process. This should include safety glasses, dust mask and cut resistant gloves. For the purpose of comfort, consider wearing knee pads, as it can take a while to remove grout. Make sure to wear pants and boots as well.

4. Remove old grout Processing

Make the center incision. Make an incision down the middle of each grout line using a grout saw, preferably one with a carbide blade. Do this to all the grout lines that you want to remove.

Remove the grout. Remove the grout from between the pieces of tile with a grout scraper, using the incision as a starting point. Insert the triangular tip of the grout scraper into the incision you made with the grout saw. Apply firm pressure and drag the scraper along the grout line about the length of one tile, but be very careful to avoid scraping the tile. Lift out the grout scraper, return to the starting point and repeat the process until you have removed all the grout in that area.

If you do not have a grout scraper, use a small, cold chisel and hammer or a knife blade. Angle the chisel away from the edge of the tile and tap if with the hammer until the grout is freed from the floor and edges of the tile.

Finish the edges. Clean up the edges of the tile by chipping out any remaining grout remnants. Hold the chisel so that it is parallel to the floor and the cutting edge of the chisel is touching the edge of the tile. Lightly tap the end of the chisel with the hammer until the grout is loosened. Sweep up the broken pieces of grout from between the crevices using a dust broom or a shop vacuum.

5 Cleaning Up After Removal

Remove tape and clean grout lines. Peel off the painter’s tape from the edge of the tile, then wash out the grout lines with soap and water. You may need a scouring pad to scrub away any remaining grout from the edges of the tile. Gently scrub the edges of the tile until the grout has been completely removed.

Clean the tile. Wipe down the tile immediately if you are planning on keeping it, and then buff the area out a few times. Grout residue can quickly harden onto the tile, making it difficult to remove without damage. Fill a spray bottle with half vinegar and half water. Spray the tile and allow the solution to sit for a couple of minutes before wiping it away with a clean cloth.

Base on this article TKT Cleaning do hop that you could remove grout by yourself with very simple tool.


Compare between commercial and domestic cleaning service

What are the difference between Commercial Cleaning and Domestic Cleaning

In a lot of scenarios, proper cleaning is very important, but it is possible to do a variety of cleaning services. Primarily, there are two types of cleaning and they are domestic cleaning and commercial cleaning. So what are the differences between these two types of cleaning?

What are the Main Differences?

The major difference between these two is that:

  • domestic cleaning is something that happens in the residential environment
  • while the commercial cleaning is something which happens in business or corporate environment.

A house owner can choose to do their own cleaning or they hire professional cleaners to do their cleaning tasks for them. Business enterprises can also employ their own in-house cleaning team or they can choose to get contract cleaners TKT Cleaning in to help them out.

There are also other differences, one is that many of the commercial cleaning processes are very different from those which are used around the home. This is partially down to the fact that these cleaning tasks are usually done on a much larger scale. Many of the tools and devices which are used to clean a large business would simply be too powerful for use in a home, and therefore they are never used in a domestic cleanup operation.

Many companies are also requires to meet special health and safety standards if they want to keep their operating license. For example, hospitals must maintain better hygiene levels if they do not want patients to catch illnesses whilst they are being cared for, and food vendors must maintain hygienic atmosphere if they want to be allowed to continue to serve food by the local food standards agency.

For those involved in commercial cleaning, it is very important that these health and safety standards are adhered to, as it could cause serious issues if they are not. With domestic cleaning, homeowners set their own standards, although these standards may be just as high in some cases. However, there are no real standards which must be met as part of a domestic cleaning job. The fact that there are no set standards in domestic cleaning makes it a much easier task for those who are doing it.

Commercial cleaning is also required far more regularly than domestic cleaning, because of the large number of employees in the office premises, and the types of activities that go on there, commercial spaces may need thorough cleaning every single day. Most domestic spaces will not need to be fresh as regularly as this.

There are many differences between commercial and domestic cleaning, but you can seek professional assistance to carry out both commercial and domestic cleaning tasks in Ho Chi Minh, you can call TKT Cleaning

Eco-friendly Cleaning Products for Both Commercial and Domestic Spaces

Eco-friendly cleaning products and tactics can be the perfect way to keep your commercial property clean and tidy as well as giving out planet the much-needed helping hand. But swapping some of the hazardous chemicals that your commercial or domestic cleaning service team uses for eco-friendly products can also ease allergies and chemical sensitivities amongst your company staff for a healthier working day. Check out these products that are completely eco-friendly and recommended by many expert contract cleaners TKT Cleaning.

Vinegar is an effective cleaning agent which is not only hazardous but also highly efficient. Vinegar has been used as a natural sanitizing agent for years and is the basis for many domestic and commercial cleaning products. So, why not use the real thing rather than harsh chemical solutions in your office or commercial environment? Vinegar kills dangerous microbes (such as bacteria) as well as removes lime deposits that are common in a number of electronic appliances in kitchens and office canteen areas.

Baking soda is another household material that can be used for cleaning in commercial environments. It is mostly known for use in baking, but it has found real time applications such as in cleaning, and many professional cleaners use it as cleaning agent even in commercial spaces. Baking soda also known as sodium bicarbonate has the ability to neutralize unpleasant odors, de-grease electronic appliances, polish silverware and clean surfaces.

These days, many professional cleaning companies do not charge you when it comes to surveying your office/home premises and provide you with a detailed specification and quote, before the actual work starts. Contact TKT Cleaning for more details.

How to kill Mold on Drywall, Wood and Tiles effectively

TKT Cleaning company continues serial post about “how to kill, remediate, prevent mold at home and office.  We offten see mold on drywall, wood, tiles and grout.

The most obvious sign of a mold problem on wall is finding green, brown, orange or even black spots. But there are other, less apparent signs:

  • Cracked or peeling paint
  • Discoloration
  • A recurrent “soot” or black streaks
  • Bulging
  • A musty, damp smell
  • Places Most Prone To Mold
phía sau tường thạch cao bị nhiễm mốc

Image: mold behind Drywall

Mold often grows in areas where condensation forms from water vapor in the air meeting a cold surface which turns the vapor into a liquid. This often takes place on exterior walls or in basements.

Very humid areas in the home are prone to mold, too. Bathrooms and laundry rooms are two common places to find mold growing, particularly on grout lines or shower walls. Other areas include the walls and ceiling near humidifiers and any room with a hot tub or jacuzzi improperly installed indoors. In these places, one of the best ways to prevent mold is to decrease humidity by opening windows and running fans regularly.

Mold also grows where there is (or has been) a water leak. Places like the cupboards under sinks are very prone to mold. Once a pipe has leaked, there’s a good chance mold will grow unnoticed within the wall until the problem requires expert removal.

  • Drywall
  • Wood
  • Tiles and grout

You need to remove mold in different ways depending on the material it’s growing on.

1. Mold on Drywall

If you find mold growing on unpainted drywall in your home you will have to remove the drywall and replace it. Unfortunately there is no way to completely remove mold from unpainted drywall since it is a porous material.

How to Remove Moldy Drywall

Use a utility knife to cut out any section of drywall with mold on it. You should make sure to cut out an area that covers at least two of the wooden beams behind the drywall. This is so you’ll be able to properly attach the replacement section of drywall onto the two beams.

Next you’ll need to cut out a section of new drywall to replace the drywall you just removed. Use a tape measure to measure out the length and width of the new section of drywall that you’ll need so that it will fit properly. Then use the utility knife to cut out the section of new drywall.

Make sure that the new drywall fits snugly in place and then use drywall screws to attach it to the wooden beams. After this you should apply joint compound (also called drywall compound or mud) and then leave it to dry. Once you’ve left it for 24 hours you can then sand the joint compound down to smooth it out. You can also then paint the drywall if you like.

It’s a good idea to HEPA vacuum the room as well to remove any mold stirred up during the process.

moc do am moc chan tuong

Image: mold on wall

Mold on Painted Drywall

If you find mold on drywall that is painted or primed then the good news is you shouldn’t have to remove the drywall. This is because the mold should be just on the surface and shouldn’t have penetrated into the drywall itself.

Wipe or scrub the mold away using a cleaning product or mold killing solution. You can find some mold killing solutions and directions on how to use them at the Killing Mold page.

2. Mold on Wood

It’s usually safe to keep using moldy wood once you’ve cleaned it up. Although there might be some small amount of mold left below the surface of the wood, it shouldn’t regrow and cause problems provided you keep the moisture in your home to a minimum. If the wood is painted then it’s even better news since the mold probably wouldn’t have penetrated into the surface of the wood.

How to Remove Mold from Wood

To clean moldy wood wipe or scrub the mold from the surface using a sponge, cloth or scrubbing brush, along with some water and detergent, or any other household cleaner. See the Killing Mold page for some effective solutions to remove mold.

You can use a mold killer if you want, such as bleach, although it isn’t necessary as the main goal is just to remove mold from the surface. There are always going to be small amounts of mold and spores in your home anyway, so trying to kill all the mold spores isn’t the aim. Plus dead mold spores are still allergenic.

The same general process for removing mold from wood applies whether the mold is on wooden furniture, wooden walls, wooden beams or any other wood.

diet nam moc tren tuong go

Image: mold on wood

Removing Mold Stains from Wood

Once you’ve cleaned mold growth off wood there might still be a mold stain left behind. Don’t worry, this is just a cosmetic problem and the mold shouldn’t regrow as long as your house doesn’t have any big moisture problems. And if you do get moisture problems then mold will grow in your home whether or not there’s a mold stain left behind anyway.

If you don’t like the look of the stain you can sand the wood if you want. This should usually remove the stain, although sometimes the mold stain might run deep into the wood so that it can’t be completely sanded away.

Another way to get rid of left over mold stains is to use a small amount of bleach to fade it away. This could discolor the wood though so it’s a good idea to do a spot test.

Removing Moldy Wood

Another option of course is to remove and replace wood with mold on it. Usually this is not worth the cost and trouble compared to cleaning, but if it’s a situation where the wood is cheap and easy to replace you might decide it’s the best option.

After Remediating Mold on Wood

You’ll need to HEPA vacuum the surrounding area once you’ve removed the mold from the wood. During mold removal it’s inevitable that some mold spores are stirred up and so you need to remove as many as possible by HEPA vacuuming.

After you’ve finished cleaning up the mold problem you might want to coat the wood with a fungicidal sealant or paint so that you know it’s completely safe. This way any mold left in the wood certainly won’t affect you and no new mold should begin to grow on the wood either.

3. Mold on Tiles and Grout

You’ll often see mold growing on tiles in places like the bathroom. The good news is that mold can easily be cleaned from the non-porous surfaces of tiles.

How to Remove Mold from Tiles and Grout

Begin by scrubbing the mold off of the tiles and grout. You should use a scrubbing brush along with a household cleaning product or mold killing product. There are also commercial tile or grout cleaners you can buy.
After this you’ll probably find there is still mold stains left on the grout. You can use bleach to fade these stains away. Before you use the bleach you should spot test it to make sure that it won’t discolor your tiles. You should also wear gloves to protect your hands from the bleach.
Apply the bleach to the grout and leave it sit for about 10 minutes. Instead of chlorine bleach you can use hydrogen peroxide if you like, or buy a product like Oxiclean which contains oxygen bleach. If you have a septic system it’s better to use oxygen bleach than chlorine bleach.
Another alternative is to use baking soda. Mix it with water to create a paste and then use a toothbrush to scrub it onto the grout.
If you find the stain remains on the grout after bleaching then repeat the process. Afterwards rinse the bleach off thoroughly with water.
If the stains won’t go away you can try using paper towels soaked in bleach. Saturate paper towels in bleach and then stick them to the grout where there are stains. Give it some time and this should fade away the mold stains on the grout.

The general conclusion on the wall fungicidal Guide as follows:

Prone to rippling walls moldy, the walls were marred due to moisture infiltration causes, create conditions for mold growth. If only intervention by the paint surface, or even re-waterproofing baits will not be able to solve the problem thoroughly. Because only a short time, or after a few rains moisture in the wall will mark new paint stains. You need to check the cause mold to handle.
Best to handle both the external borders and the inside of the wall where the mold. After processing precision mold causes the wall to dry waiting for new surface treatment. Attention should not paint the walls when wet weather too much.

With articles fungicide guide on drywall, wood, ceramic tiles  TKT cleaning company hope you can take to clean up mold in your home efficiently.

9 Product kill mold effectively

9 Product kill mold effectively

Cleaning company TKT continued articles about how to eliminate mold. Maybe you will be interested in the current chemicals used to kill mold is what? The following article will give you 8 kinds of chemical helps effectively eliminate mold.

There are several products you can use to kill and remove mold. Some of the most effective mold removal products include:

  • Bleach
  • Borax
  • Vinegar
  • Ammonia
  • Hydrogen peroxide
  • Detergent
  • Baking soda
  • Tea tree oil
  • Grapefruit seed extract

Mold Removal with Bleach

Bleach can kill virtually every species of indoor mold that it comes into contact with, along with its spores, leaving a surface sanitized and resistant to future mold growth.

Unfortunately, however, using bleach is only effective if the mold is growing on non-porous materials such as tiles, bathtubs, glass and countertops. Bleach cannot penetrate into porous materials and so it does not come into contact with mold growing beneath the surface of materials such as wood and drywall. Using bleach on these materials will kill the mold above the surface but the roots within the material will remain and the mold will soon return.

How to Kill Mold with Bleach

Bleach produces harsh fumes so make sure the area is well ventilated before you begin. You should also wear gloves during the process to protect your hands.

  1. For killing mold with bleach use a ratio of one cup of bleach per gallon of water (ie about 1 part bleach to 10 parts water).
  2. Apply the solution to non-porous surfaces with mold growth either by using a spray bottle or by using a bucket and a sponge or cloth.
  3. You don’t need to rinse the surface afterwards (unless it is used for food preparation or a surface which may be touched by small children or pets) as the bleach will inhibit mold growing in the future.

Does Bleach Kill Mold?

Although the active ingredient in bleach, sodium hypochlorite, is the main ingredient in many mold removal products, there are many reasons to use alternatives to chlorine bleach when killing mold.

One reason is that bleach cannot completely kill mold growing in porous materials. The chlorine in bleach cannot penetrate into porous surfaces such as drywall or wood. The chlorine is left on the surface of porous materials and only the water component of the bleach is absorbed into the material, providing more moisture for the mold to feed on.

Some of the mold on the surface might be killed but the roots of the mold are left intact meaning the mold soon returns, leaving you in a cycle of repeated bleaching. Perhaps this is why some people believe that spraying bleach on mold doesn’t affect it but instead just bleaches its color so you can no longer see it.

Another disadvantage of bleach is that it can damage the materials it’s used on as it is a harsh, corrosive chemical. Chlorine bleach also gives off harsh fumes and it even produces toxic gas when mixed with ammonia. There are safer alternatives such as borax or vinegar which don’t produce dangerous fumes or leave behind toxic residue. For these reasons try to avoid using bleach and if you must use it, only use it on non-porous surfaces.

Mold Removal with Borax

There are many advantages to using borax to kill mold. For starters, borax is a natural cleaning product and although it is toxic if you swallow it, borax does not emit chemicals or dangerous fumes like some other mold killers. Borax, a white mineral powder, has a pH level of about 9 (baking soda is pH 8.1 and pH 7 is neutral) and a low toxicity.

Borax is commonly used as a deodorizer as well as for cleaning toilets and drains. Borax is also used as an insecticide, herbicide and fungicide and it can be mixed with water in a solution to kill and remove mold as it is a natural mold inhibitor. You can buy borax in supermarkets for a few dollars from the laundry section.

How to Kill Mold with Borax

  1. To kill mold using borax, create a borax-water solution using a ratio of 1 cup of borax per gallon of water.
  2. Vacuum up any loose mold with a HEPA filtered vacuum cleaner to lessen the number of spores stirred up into the air during the cleaning process.
  3. Use a scrubbing brush with the borax-water solution to scrub the mold off the surface.
  4. Wipe up any extra moisture and excess mold particles or dust/debris to prevent them spreading into the air once the surface has dried.
  5. You don’t need to rinse off the borax as the solution will prevent more mold beginning to grow on the surface again.
  6. Leave the surface to dry completely.

Mold Removal with Vinegar

Vinegar is a mild acid which can kill 82% of mold species. However it also has the advantages of being natural and safe. Vinegar is non-toxic and doesn’t give off dangerous fumes like bleach does.

How to Kill Mold with Vinegar

To kill mold with vinegar, use white distilled vinegar which you can buy cheaply from the supermarket.

  1. Pour some vinegar into a spray bottle without watering it down.
  2. Spray the vinegar onto the moldy surface and leave it to sit for an hour.
  3. Wipe clean the area with water and allow the surface to dry. Any smell from the vinegar should clear within a few hours.

If you want to use vinegar to prevent mold growing on surfaces just spray vinegar on the surface and leave it. Repeat this every few days to ensure the surface will stay mold-free. You can even mop your tiled bathroom floor or other hard non-porous floors with vinegar if you are worried about mold growing on them.

Mold Removal with Ammonia

Like bleach, ammonia will kill mold on hard non-porous surfaces such as countertops, glass or tiles but it is ineffective at killing mold growing in porous material such as wood or drywall.

Another disadvantage of using ammonia is that it is a harsh, toxic chemical. Make sure you never mix ammonia with bleach because the gas they create when combined is toxic. Chlorine mixed with ammonia was even used as a chemical weapon during World War 2.

Additionally, although ammonia can kill surface mold, dead mold and dead mold spores are still allergenic so you will need to make sure to remove them afterwards.

How to Kill Mold with Ammonia

  1. To kill mold using ammonia, create a solution of 50% clear ammonia and 50% water in a spray bottle and spray it on moldy areas.
  2. Make sure the ammonia you use says “clear ammonia” on the label.
  3. Leave the area for a few hours before wiping and rinsing.
  4. Often detergents or mold cleaning products will contain ammonia. In that case just follow the directions on the label and be sure never to mix it with bleach.

Mold Removal with Hydrogen Peroxide

Hydrogen peroxide kills mold as it is anti-fungal as well as anti-viral and anti-bacterial. Hydrogen peroxide is a good alternative to chlorine bleach because it is safe to use and doesn’t damage the environment, nor does it leave behind toxic residue or produce toxic fumes like chlorine bleach does. You can buy hydrogen peroxide from drug stores for around one dollar for a bottle of 3% concentration.

Hydrogen peroxide kills mold effectively on many materials such as clothes, floors, bathroom fixtures, walls and items such as kitchen appliances. Since hydrogen peroxide is a bleaching agent it may also help fade the stain mold leaves behind. Spot test hydrogen peroxide on the material you’re going to be cleaning to make sure it won’t fade the material’s colors.

How to Kill Mold with Hydrogen Peroxide

  1. To kill mold pour 3% concentration hydrogen peroxide into a spray bottle.
  2. Spray the moldy surface completely so that the moldy areas are saturated with hydrogen peroxide.
  3. Leave the surface to sit for 10 minutes while the hydrogen peroxide kills the mold.
  4. Then scrub the area to make sure to remove all the mold and mold stains.
  5. Finally wipe the surface down to remove residual mold and spores.

You can also use vinegar with hydrogen peroxide during the cleaning to more effectively remove the mold. Afterwards store the spray bottle in a dark place since light diminishes hydrogen peroxide’s effectiveness.

Mold Removal with Detergent and Water

A solution of detergent and warm water can be used to scrub surface mold off non-porous surfaces. Although detergent itself doesn’t kill mold, if the mold is on non-porous materials then the solution doesn’t need to kill it as long as you completely clean away all the mold on the surface.

Mold Removal with Baking Soda

Baking soda is well known as a natural and safe household cleaner. But you can also use baking soda to kill mold in your home. Unlike other mold killers which contain harsh chemicals, baking soda is mild (pH of 8.1) and harmless to your family and any pets.

Besides killing mold, baking soda also deodorizes and so using it can get rid of the smell mold leaves in your home. Baking soda also absorbs moisture to help keep mold away.

Vinegar is often used along with baking soda when cleaning up a mold problem since vinegar kills different species of mold to baking soda.

How to Kill Mold with Baking Soda

  1. Add one quarter of a tablespoon of baking soda to a spray bottle of water.
  2. Shake the bottle to dissolve the baking soda into the water.
  3. Spray the moldy area with the baking soda and water solution.
  4. Then use a sponge or scrubbing brush to make sure to remove all the mold from the surface.
  5. Once you’ve scrubbed away the mold rinse the surface with water to remove any residual mold on the surface.
  6. Spray the area with the spray bottle again and let the surface dry. This will kill any left over mold and prevent the mold returning.

You can use a cloth instead of a spray bottle to clean mold with baking soda:

  1. Soak a cloth in water and then add one quarter of a tablespoon of baking soda to it.
  2. Use the cloth on the moldy area to remove the mold with the baking soda and water solution.

Mold Removal with Tea Tree Oil

Of all the natural mold killing solutions tea tree oil is the most effective. Although it is also expensive, a small amount of tea tree oil goes a long way in killing mold.

Tea tree oil is an essential oil which is harmless to people and pets. Tea tree oil is antifungal, capable of killing all types of molds. Tea tree oil is antibacterial as well.

You can buy tea tree oil for about $10 for a small bottle from most natural food stores. Make sure the tea tree oil you buy is derived from the Melaleuca Alternifolia, which is the technical name for tea tree, as not all brands always are.

How to Kill Mold with Tea Tree Oil

  1. To kill mold using tea tree oil add water to a spray bottle, keeping in mind how many cups it takes to fill the bottle.
  2. Next add tea tree oil at the ratio of 1 teaspoon per cup of water that went into the spray bottle.
  3. Spray the solution on the moldy surface.
  4. There is no need to rinse since leaving the tea tree oil on the surface will kill the mold and prevent it from returning.

An alternative to using a spray bottle is to use a rag or cloth with the tea tree oil solution to clean away mold:

  1. First create a solution of tea tree oil and water in the ratio of 1 teaspoon per cup of water.
  2. Use a cloth to apply the solution to the moldy surface and scrub the mold away.
  3. Again, you do not need to rinse the surface afterwards.

Tea tree oil has a strong smell but it will go away after some time. You can keep and use the solution you have made for a long time afterwards as tea tree oil does not lose its potency quickly.

Mold Removal with Grapefruit Seed Extract

Grapefruit seed extract is similar to tea tree oil in that it is an expensive but very effective natural mold killer. The advantage of grapefruit seed extract over tea tree oil however is that it has almost no odor. Like tea tree oil you can buy grape fruit seed extract from most health food stores.

Grapefruit seed extract kills mold naturally as the citric acid from the grapefruit attacks mold. Grapefruit seed extract also disinfects areas and deodorizes as well. Like tea tree oil, a small amount of grapefruit seed extract goes a long way in killing mold.

How to Kill Mold with Grapefruit Seed Extract

  1. To kill mold with grapefruit seed extract create a solution of grapefruit seed extract and water in a spray bottle in the ratio of 10 drops of grapefruit seed extract per cup of water.
  2. Shake the spray bottle to mix the solution thoroughly and then spray it onto the surface where mold is growing.
  3. You do not need to rinse the solution away afterwards although you can use a cloth to wipe away the mold and solution after some minutes if you like. The longer grapefruit seed extract is in contact with mold the more it will cut through and kill the mold colony and prevent mold from returning.
  4. Repeat if needed to more thoroughly remove mold from the surface.

The grapefruit seed extract solution in the spray bottle will remain potent for a long time and can be reused again and again as grapefruit seed extract has a long shelf life.

How about cleaning service in Vietnam

There are some question and answer about cleaning service in Vietnam let us understands about cleaning industrial in Vietnam.

Image: cleaning service in Vietnam – TKT Cleaning

1.What are the strengths of the Vietnamese cleaning industry? Could you illustrate this with an example from your own company?


  • Price;
  • Understand need of customers and workers (cleaners);
  • Quickly learn and update cleaning technology

2. In what way can the Vietnamese cleaning industry still grow? What are the challenges?


  • Yes they can.
  • The challenges are: lack of investment to technology, labor and quality assurance  in long term lead unprofessional service.

3. How would you describe the current state of the cleaning industry? Is it very organized?


  • It’s very competitive with so many small and new companies. Not yet organized.

4. Do you see a lot of growth of the professional cleaning industry? How has your company developed over the past few years?


  • Yes we see.
  • We have just a little bit development but not much. We are lack of investment to build a professional service and to assure cleaning quality.

5. What does training consist of? Do you need certain certificates as a cleaner or company?

  • Training for involve big projects, for recruitment and keeping of cleaning quality.
  • Yes we need.

6. How are the wages generally?

The wages increase yearly about plus 10%. The wage including:

  • Salary about 4,500,000 vnd/month
  • Assurance about 1,000,000 vnd/month
  • Salary for 13th month. 4,500,000 vnd/year
  • Profits for holiday about 1,000,000 vnd/year


How to renting a steam carpet cleaner

When your carpet needs a deep cleaning, consider renting a carpet steam cleaner.

Heavy foot traffic can make carpets especially dirty. When considering whether to clean the carpet on your own, try renting a steam carpet cleaner, which uses detergent and hot water to loosen dirt from the carpet and then extracts it.

Angie’s List members reported paying an average of about $51 per room in 2014 for professional carpet cleaning, while average rates for carpets cleaned by the size instead of the room ranged between 30 and 50 cents per square foot. It’s possible to rent a steam carpet cleaner for an average of $35 per day, plus cleaning solution.

In addition to cost, keep the following factors in mind before proceeding with a carpet steam cleaner rental.

1. How long do I need to rent a carpet steam cleaner?

Most people rent a carpet steamer for a day.

Consider how many rooms you’ll be cleaning to determine whether 24 hours is long enough, or whether you need a carpet cleaner rental for a longer period of time.

Check with the rental company to see whether they will give you a better daily rate for multi-day rental. Be generous with your projection for how long cleaning might take.

2. Do I need to buy carpet cleaning detergent?

Rental companies recommend that you use a specific type of cleaning solution with their steam cleaners. For example, a company might make one type of cleaning agent for upholstery and another one with a stronger concentration for carpets.

Verify in advance that you are using the right cleaning detergent. If you want more options, ask the rental company whether the machine is compatible with other detergent brands.

3. Is my carpet steam cleaner certified?

The Carpet and Rug Institute represents carpet manufacturers nationwide, and tests steam cleaners to determine whether they effectively clean carpets. If the steam cleaner passes the CRI testing procedure, it receives a bronze, silver or gold certification.
Before renting, make sure the steam cleaner is CRI-certified for a specific level of cleaning power and effectiveness.

4. How portable is the steam carpet cleaner?

Keep in mind the weight of the machine you plan to rent. Not only will you have to load and unload it into your vehicle when transporting it, but you’ll also have to push it around the house as you clean.

Don’t forget that the machine’s weight will increase as you add water and cleaning solution to the tank.

5. How long will it take my carpet to dry?

If this is your first carpet cleaner rental, consider drying time can range from a couple of hours to more than 10 hours.

Drying time increases for carpets with heavy stains, which require more cleaning solution to clean. Make sure no one walks on them until they’re dry; otherwise, they will get dirty again rather easily.

Have you rented a carpet steam cleaner? Tell us about the results in the comments section below.

Hot water extraction vs steam cleaning. Difference?

The fact is, most people refer to hot water extraction as steam cleaning when in actuality, they are two entirely different cleaning processes. Each method uses a different temperature of water and sometimes different cleaning solutions as well. So before you clean your carpet or try to treat a nasty stain, read on to learn more about hot water extraction vs steaming cleaning.

Hot Water Extraction vs Steam Cleaning


The primary difference between hot water extraction vs steam cleaning is the temperature of the water used. It’s basic science, really.

For a carpet to be steam cleaned, it must actually use steam. I know—who would have guessed? The water must reach a temperature high enough to transform into a gas. However, applying pure steam to carpet will not be effective in rinsing.

Hot water extraction, on the other hand, only requires hot water. How hot? Hot enough that it cleans deeply and effectively, but not so hot that it changes into another state of matter.

giat tham hoi nuoc nong

Figure: steam carpet cleaning


Most carpet manufacturers recommend that their products be cleaned with hot water extraction. Natural fibers are cleaned with hot water extraction to prevent shrinkage, as is upholstery. It can be used to treat stains as well, unlike steam cleaning, which is avoided because it can actually set stains permanently. Steam cleaning is often used with synthetic carpet, and some people believe the higher level of heat will improve the cleanliness of their carpet.
However, homeowners should beware of renting or buying products like extractors and steamers to use at home. Inexperience and subpar equipment could lead to soaking of your carpet and a large amount of detergent residue, while inadequate ventilation could cause mold growth.

If you use a professional cleaner, the hot water extraction method will work well if they avoid high levels of detergent and detergent residue, which attracts dirt and can quickly make your carpet dirty again. This is ideal if you or your family are concerned about exposure to volatile chemical compounds. Professionals will also make sure that most of the water sprayed on the carpet is removed. The process doesn’t take long and usually involves four simple steps. They’ll start with an inspection of the area, then they’ll apply an emulsifier or detergent, next they will rinse the carpet clean with water, and finally they will vacuum out nearly all of the water. Within a couple of hours, your carpet will be dry again and ready for use.

Hot Water Extraction vs Steam Cleaning


So hot water extraction vs steam cleaning: which is best? The titles have become so jumbled that it’s hard to say, but hot water extraction is essentially superior. With pure steam, there is no “rinsing” of the fibers, which is necessary to remove soil and cleaning detergents.
The most important thing to note is that within the carpet industry, hot water extraction is increasingly being referred to as “steam cleaning.” If you’re confused as to which service a company offers, just ask, but it’s very likely that they use hot water extraction under the name steam cleaning. While most professional carpet cleaners use water hot enough to visibly produce steam, there is still hot water rinsing and flushing the carpet fibers. Not pure steam.

How To Remove Mold From Clothes

There are a few different ways to remove mold from your clothes. Some of the best are:

  • Bleach
  • Borax
  • Vinegar
  • Mold killing detergent
  • Dry cleaning
  • Brushing clothes
  • Lemon juice
  • Baking soda
  • Hydrogen peroxide
hoa chat giup diet nam moc tren quan ao

Figure: substance good at removing mold

After you wash your clothes let them dry on the clothes line in the sunlight. If you try one of the below methods and still find mold on your clothes you might have to try another method to completely remove the mold.

nam moc xuat hien tren quan ao

Figure: mode on clothes

Bleach to Remove Mold From Clothes

A well known way to remove mold from clothes and fabric is to wash them with bleach. Adding one cup of bleach to the washing machine when you wash a load of clothing should be effective in removing mold from clothes. Check the directions on the bleach to confirm and also check your clothes for do not bleach warnings and perhaps do a spot test for color fastness.

Borax to Remove Mold From Clothes

Another product you can use to wash clothes with to remove mold is borax. Use half a cup of borax in hot water to make sure it dissolves when washing your clothes in the washing machine.

Vinegar to Remove Mold From Clothes

Vinegar can kill 82% of all mold species. Add one or two cups white vinegar to the washing machine when washing moldy clothes. Repeat if needed.

dam giup diet nam moc

Figure: Vinegar helps remove mold

Mold Killing Detergent to Remove Mold From Clothes

There are washing detergents specially made not only to wash and clean your clothes but to also remove mold on your clothes in the wash. Two mold killing detergents are Oxiclean and Clorox.

Dry Cleaning to Remove Mold From Clothes

If dry clean only clothes develop mold then you won’t be able to wash them with mold killing products. Fortunately dry cleaning clothes can be an effective method for removing mold from any clothing because of the heat used during dry cleaning.

Cleaning to Remove Mold From Clothes

You can remove mold from your clothes without having to us any additional products by brushing the mold off and then washing the clothes. Take your clothes outside the house and brush the mold to remove as much loose mold as you can. After this leave them out in the sun. The sunlight can kill the remaining mold on your clothes.

Next soak the clothes in cold water. Then wash your clothes as usual with hot water. Afterwards hang them on the line to dry in the sun.

diet nam moc khi giat quan ao

Figure: Remove mold by wash machine

Lemon Juice to Remove Mold From Clothes

Apply lemon juice on the mold stain on your clothes. You can also sprinkle salt on it too for extra effectiveness. After leaving the clothes in the sun until dry, rinse them and then launder as usual.

Baking Soda and Hydrogen Peroxide Remove Mold From Clothes

Some other remedies for removing mold on clothes are baking soda and hydrogen peroxide. Follow the directions on the products you buy.

Why Mold Grows on Clothes

If you have clothes that are wet for more than 24 hours then mold can easily start to grow on them.

The most common reason mold grows on clothes is if you wash them and then leave them wet for a long time. After you wash your clothes you should dry them immediately. Drying clothes on the line in the sun is the best. And only put your clothes away once they are completely dry.

The same is true for clothes that are damp after you wear them. These need to be washed quickly (the same day) or hung somewhere to air out. Make sure not to leave damp clothes in a wet pile or the hamper for days on end.

The other main reason that clothes grow mold on them is if the air in your home is too humid. Rooms where you store clothes need to be properly ventilated. Hanging clothes with some space between them in the closet or not packing them in too tightly together in drawers help the clothes air out when they are stored away.

Mold Destroys Clothes

Mold on clothes can be a common problem in the home. If you find mold on your clothes it’s important to remove it quickly. The longer mold is left on clothes the harder it will be to remove.

Mold slowly eats the organic material it’s growing on, such as cotton clothes. The longer you wait to remove mold from your clothes the more deteriorated they will become. Moldy clothes begin to smell bad too.

Symptoms from Mold on Clothes

Another good reason to quickly remove mold from clothes is the symptoms it causes. Breathing in mold spores from clothes can cause allergic reactions like sore eyes and sneezing. You can also get skin rashes and itchiness from wearing clothes with mold on them.

You do not have to be wearing moldy clothes to suffer symptoms from them though. If there’s mold on your clothes they’ll release spores into the air of your home. These spores build up inside the home and affect the indoor air quality and your health. Chances are that this will make the mold problem spread from your clothes and mold will begin to grow around your home.

Cleaning company TKT would like to express our customers understand more about mold

Does Bleach Kill Mold

This article will help you understand how to kill mold using bleach is derived from Chlorine and Oxygen

This page tells you how to kill mold with:

  • Chlorine bleach
  • Oxygen bleach

The Mold Removal page also provides a step by step guide to the entire mold removal process.

The Mold on Clothes page has information about removing mold from clothes with bleach and other mold killing solutions.

1. Chlorine Bleach Information

Bleach is probably the most well known mold killer. In fact many commercial mold killing products contain bleach. The active ingredient in chlorine bleach is sodium hypochlorite, but otherwise it is mostly made up of water.

Bleach is cheap and you can easily buy it at the supermarket. You will often see it labeled as laundry bleach or just bleach, instead of chlorine bleach.

2. Does Bleach Kill Mold

Bleach kills bacteria and viruses and sanitizes the surfaces it’s used on. Bleach also kills mold if it comes into contact with it. The spores and allergens from mold are neutralized as well.

Bleach will kill mold growing on non-porous surfaces like glass, tiles, bathtubs and counter tops. However bleach cannot completely kill mold growing in non-porous materials like drywall and wood. Bleach does not penetrate into these non-porous substances and so only the mold growing above the surface is killed.

hóa chất tẩy trắng làm sạch

Image: Bleach

3. How to Kill Mold with Bleach

  • Before you start you should open the doors and windows to ventilate the area.
  • Bleach damages your skin so it’s a good idea to wear protective gloves. You might also want to wear eye protection too.
  • Start by mixing the bleach with water. The ratio should be one cup of bleach per gallon of water. This is about a one part bleach to ten parts water ratio. Make sure to check the instructions on the bleach as well in case it recommends something different.
  • Next apply the bleach to the moldy surface. You might want to use a spray bottle or a cloth or sponge. Bleach can slowly destroy sponges and cloths though, so you might not be able to use them again after.

4. Should You Use Bleach to Kill Mold?

The EPA does not recommend you use bleach for killing and removing mold. Bleach is a chemical, and it is better to use natural mold killing products instead. Some good alternative mold killing products are borax and vinegar. Bleach also loses its power with time. Even if bleach is not opened, in 90 days it loses 50% of its killing effectiveness.

Another disadvantage is that bleach is corrosive. Bleach deteriorates materials and the fibers of porous substances. The gas from bleach can even damage your lungs. If bleach touches your skin it can also give you chemical burns.

There is also concern about whether bleach leaves dioxins. Dioxins are highly toxic and carcinogenic substances. They are also teratogenic and animal tests have shown dioxins can cause birth defects.

Bleach can create dioxins in processes like bleaching of wood pulp. Fortunately though, studies have found that bleach cannot form dioxins when it’s just used for household cleaning. The materials which are needed for bleach to form dioxins are not usually present when cleaning the home.

Bleach is ineffective at killing mold on many materials, including carpet and upholstery. Bleach won’t kill mold on dirty, metallic or porous substances either.

5. Why Bleach Does Not Kill Mold on Porous Material

You should avoid using bleach to kill mold on porous materials. Because of its ionic structure, bleach cannot soak into substances which are porous. So the chlorine stays above the surface, while the water is absorbed in.

This means bleach will only kill the mold on the surface of porous materials like wood and drywall. The mold’s roots are left alive and this can lead to mold soon growing back. Therefore you can end up in a cycle of continually trying to bleach mold, only to have it constantly return.

6. Oxygen Bleach to Kill Mold

A good alternative to chlorine bleach is oxygen bleach. Oxygen bleach also kills mold and works well for cleaning mold from surfaces and clothes. Oxygen bleach cleans stains and kills bacteria too. It will sanitize, disinfect and deodorize whatever you use it on.

Oxygen bleach is another name for sodium percarbonate. You can buy it in a powder which you then mix with water. Once you’ve added water, the oxygen bleach powder dissolves and breaks down into hydrogen peroxide (which breaks down to water and oxygen) and sodium carbonate (also called sodium ash). These by-products are non-toxic and environmentally safe.

Many cleaning products contain oxygen bleach (eg. Oxiclean). You can buy oxygen bleach from the supermarket cheaply, where it usually only costs a few dollars.

Hình ảnh: hóa chất tẩy trắng gốc oxi diệt nấm mốc

Image: oxygen bleach

7. Advantages of Oxygen Bleach

Oxygen bleach has many differences and advantages compared to chlorine bleach. Oxygen bleach deodorizes and kills mold and bacteria but, unlike chlorine bleach, oxygen bleach is environmentally friendly. There is no phosphorous or nitrogen in oxygen bleach. Its ingredients are natural and biodegradable.

Another advantage over chlorine bleach is that oxygen bleach doesn’t fade or deteriorate clothes. You can also use oxygen bleach with hot or cold water. Oxygen bleach doesn’t fade surfaces such as wood either.

Gas from chlorine bleach is bad for you and it creates toxic fumes if you mix it with vinegar or ammonia. But oxygen bleach does not create any fumes. It can also be used safely with other household cleaners and detergents.

Both chlorine bleach and oxygen bleach can be bought cheaply from the supermarket.

8. Disadvantages of Oxygen Bleach

Oxygen bleach products are usually a little bit more expensive than chlorine bleach products. Chlorine bleach also works faster than oxygen bleach.

Oxygen bleach loses its killing power much faster than chlorine bleach too. For best results, you should use oxygen bleach within the time stated on the product’s packaging.

9. How to Kill Mold With Oxygen Bleach

  • The general directions for using oxygen bleach should be in the instructions on the packaging. You should be able to follow these to kill and remove mold.
  • Usually you begin by adding the oxygen bleach powder to water. It’s best to use warm or hot water, as this will dissolve the oxygen bleach better.
  • The ratio of bleach to water is usually between half a cup and one cup, per gallon of water. However, make sure to check for the ratio that the directions on the oxygen bleach recommend.
  • You can add the oxygen bleach and water solution to a sprayer or squirt bottle to apply it to the moldy surface. If you prefer, you can put the oxygen bleach and water mixture in a bucket, and apply it with a cloth, sponge or scrubbing brush.
  • After you have applied the solution to the mold, let it sit for about 15 minutes.
  • Then rinse thoroughly and wipe the area with water.
  • You can also make a paste if you prefer. Add just enough water to the oxygen bleach powder to make it into a paste.
  • After you mix oxygen bleach with water, the solution will be active for about 5 or 6 hours. You should dispose of it after this. It’s fine to pour the solution down the drain, as oxygen bleach deodorizes drains.
hóa chất tẩy trắng gốc oxi

Image: bleach from oxygen

Articles on this company TKT cleaning company help you have more information about how to kill mold from the chemicals simply cheap , easy to use. Cleaning company in Vietnam TKT can consult to help you have a deeper knowledge about the unpleasant mildew . You may also be interested in the article ” guidance kill mold naturally ” . TKT sanitation services wish you health and happiness always .


Cleaning, Sanitizing and Disinfecting With Bleach

Cleaning, Sanitizing and Disinfecting With Bleach – For early care and education facilities

1. Clean first

Scrub with soap and warm water and rinse. Always clean surfaces to remove visible soil before sanitizing or disinfecting to remove all dirt and contamination.

Hình ảnh: vệ sinh trước khi khử trùng bằng chất tẩy trắng

Hình ảnh: vệ sinh trước khi khử trùng bằng chất tẩy trắng

2. Next mix bleach solution

Mix bleach with cool water. Mix fresh solutions daily. Do not mix liquid bleach with other cleaning products, toilet bowl cleaners or ammonia, which may release hazardous gases into the air.

Then sanitize or disinfect.

  • Wet entire surface until glistening.
  • Leave solution on surface for two minutes.
  • Dry with a paper towel or air-dry.

Store all cleaning products where children cannot reach them.

  • Sanitizing: Reducing germs on surfaces to safer levels
    • Sanitize after EACH use:
      • Children’s mouthed toys
      • Food service areas, dishes
    • Sanitize daily or when soiled:
      • Dishcloths, synthetic sponges
      • Common surfaces (other than in bathrooms), floors, mats, tables, countertops and hard surfaces, door knobs, etc.
Hình ảnh: tiêu độc vệ sinh bề mặt bằng thuốc tẩy trắng

Hình ảnh: tiêu độc vệ sinh bề mặt bằng thuốc tẩy trắng

  • Disinfecting: Destroying or inactivating most germs
    • Disinfect after EACH use:
      • Diaper changing surface
    • Disinfect daily or when soiled:
      • Bathroom areas: ƒ Toilet bowls and seats and flush handles
      • Toilet training equipment
      • Sinks, faucets

3. Mixing Sanitizing and Disinfecting Solutions

1 pint solution

  • Sanitizing 10 drops bleach/pint water
  • Disinfecting ½ tablespoon bleach/pint water


Hình ảnh: pha 1 bình hóa chất tiêu độc vệ sinh, khử trùng

Hình ảnh: pha 1 bình hóa chất tiêu độc vệ sinh, khử trùng

1 quart solution

  • Sanitizing ¼ teaspoon bleach/quart water
  • Disinfecting 1 tablespoon bleach/quart water
Hình ảnh: pha 1 can hóa chất tiêu độc vệ sinh, khử trùng

Hình ảnh: pha 1 can hóa chất tiêu độc vệ sinh, khử trùng

1 gallon solution

  • Sanitizing 1 teaspoon bleach/gallon water
  • Disinfecting ¼ cup bleach/gallon water
Hình ảnh: pha 1 xô hóa chất tiêu độc vệ sinh, khử trùng

Hình ảnh: pha 1 xô hóa chất tiêu độc vệ sinh, khử trùng

These are the guidelines of the TKT Cleaning company about disinfection , sanitation and cleaning can apply to schools , especially kindergartens , elementary help prevent the spread of germs in the environment school. Cleaning Service for school of TKT Cleaning are also available to provide advice and service to customers .

12 Step Carpet Cleaning Process

TKT cleaning company introduce our Carpet Cleaning Process:

Step 1: Pre-Inspection

Our technician will walk through your home with you to visually inspect the carpet. He will identify potential permanent stains and give you an evaluation of expected results, as well as listen to any concerns you may have.

Step 2 Carpet Agitation

Your carpet will be agitated to allow the fiber to stand straight up to provide a thorough vacuuming.

Step 3: Commercial Pre-vacuum

Dry soil is removed by thoroughly commercially power vacuuming. Removing dry soil is one of the most vitally crucial steps in any cleaning process.

Step 4: Furniture Moving

Our regular pricing includes moving sofas, chairs, tables and smaller items. Beds, dressers, and heavier pieces cost extra to move. One of our consultants can quote the exact cost to move any heavier pieces.

Step 5: Pre-spray & Pre-Spot

A preconditioning agent is applied to emulsify and break down traffic area soil and general spots for a more thorough cleaning. Difficult spots are pre-treated with special solutions to increase chances of removal.

Step 6: Pre-grooming/Agitation

A professional carpet groomer or rotary brush is used to further loosen the soil.

Step 7: Soil Extraction and Rinse

The carpet is then thoroughly rinsed using a powerful extraction cleaning system without over wetting the carpet or leaving a sticky residue behind.

Step 8: Neutralizer

Every carpet that we clean is pH balanced afterwards so that there is no sticky residue left behind. This also leaves your carpet soft and fresh.

Step 9: Post Spot

Any spots or stains still remaining will get extra treatment with our many specialty spotting solutions. * For longer carpet life and fewer permanent stains, be sure to have professional carpet protector applied to your carpet.

Step 10: Post Groom

Your carpet is groomed with a professional groomer so that the pile of your carpet is standing tall when we leave. Post grooming helps the carpet pile dry faster and in the right position.

Step 11: Speed Dry

High velocity air movers are placed on the carpet immediately after cleaning to promote faster drying.

Step 12: Post Cleaning Inspection

Our technician will walk through your home with you to point out the cleaning results to make sure that you are completely thrilled with the job.

Best Carpet Cleaning Methods

There are many misconceptions about carpet cleaning. One of them has to do with carpet cleaning methods. What’s the best method? That depends. You have probably heard the terms “dry” or “steam”. These are general terms that hint at different methods, but both terms are incomplete and inaccurate terms. Neither are technical terms that properly describe carpet cleaning methods.

There are 4 methods of carpet cleaning approved by the Institute of Inspection, Cleaning, and Restoration Certification (IICRC), the world’s most recognized body of certification for carpet and upholstery cleaners.

Method 1: Hot Water Extraction

Otherwise known as “steam cleaning”, hot water extraction is the process that most are probably familiar with. Hot water extraction is the correct technical term, not steam cleaning. Actual steam is not used at all. A hot water solution is produced and immediately recovered, creating a “flushing” action on the carpet. There are many variations of hot water extraction. From the most powerful truck-mounted machine down to the small portable machine rented from the grocery store. What’s the difference? Every machine has different capabilities. Mainly the pressure in which the water is produced and the recovery capability.

However, the biggest and most important difference is in the person cleaning the carpet. A trained technician will know what pressure to use, what cleaning products to use, and how to get maximum soil removal and maximum spot removal without over-wetting the carpet or leaving a sticky residue behind. The horror stories of carpet being wet for days is due to operator error, not because “steam” or “hot water extraction” caused it.

Hot Water Extraction done properly will remove more soil than any other method. Further, anything that has seeped into the backing such as urine, coffee, beverages or something can be “flushed out” with hot water extraction. It can also be used in lightly soiled and maintenance situations as it is very versatile.

Method 2: Absorbent Pad

Also known as bonnet cleaning, this method employs a round pad that spins across the surface of the carpet, absorbing the soil. A solution is applied to the carpet or the pad to aid in releasing soils. This is a method that some may classify as “dry cleaning” although water based products are used in almost all “dry cleaning” systems, therefore the term dry cleaning (cleaning with only a solvent based cleaner) is not technical and would not be desired. Absorbent pad cleaning is not a deep cleaning method. It should only be used in lightly soiled and maintenance situations.

Method 3: Dry Compound

This method uses a powder that has been treated with detergents, water, and solvents. The powder compound is sprinkled onto the carpet and a brush with cylindrical brushes is used to work the powder into the carpet pile. The solution that is in the powder releases the soil. The soil is then absorbed into the absorbent powder. This method should only be used in lightly soiled and maintenance situations.

Method 4: Shampoo or Dry Foam

In this method, a shampoo or foam is generated and worked into the carpet with a rotary brush or cylindrical brush machine. The shampoo or foam releases the soil. The soil is then vacuumed with the machine or allowed to dry and removed with a conventional vacuum cleaner. This method should be used in only lightly soiled situations and maintenance cleaning. When using shampoo, great care should be taken to avoid leaving a sticky residue on the carpet.

Note: TKT Company is one of the best carpet cleaning service. We offer a 12 step cleaning program that gets maximum soil removal, maximum spot removal without over-wetting the carpet or leaving a sticky residue behind. Guaranteed or your money back!

Comparison of Carpet Cleaning Methods

What is the best way to clean carpet? There are four basic methods for cleaning carpet:

  • Carpet Shampooing
  • Dry Powder Method
  • Bonnet Cleaning
  • “External Extraction”
dich vu giat tham van phong chuyen nghiep

Figure: Carpet cleaning

1. Carpet Shampoo – Carpet cleaning Method

The theory in the shampoo method is to generate a lot of foam in the carpet, allow this foam to dry, have the resulting residue attract the soil and vacuum up the residue and soil the next day.

Carpet shampoo products must have the following characteristics which dictate their ingredients:

  • Very high foam levels to reduce wetting.
  • Very stable foam.
  • High lubricity to reduce damage to the carpet fibers from the brushes.
  • Dry to a non-sticky residue.

Therefore, a carpet shampoo must contain a very foamy chemical. The most common ingredient is sodium lauryl sulfate or one of its relatives. Sometime when you’re taking a shower or bath, look at the ingredient statement on your hair shampoo bottle. It will say “Contains sodium lauryl sulfate” or some similar wording. Sodium Lauryl Sulfate and its relatives exhibit a very high and very stable foam and are only fair detergents. The problem is that they dry to a soft, sticky residue which will cause resoiling.

Because of the resoiling problem, carpet shampoos will frequently also have an anti-resoiling additive such as a resin to reduce this resoiling tendency.

Because shampoos are actually very poor detergents and basically simply bury the dirt, they frequently also contain high levels of optical brighteners which take invisible ultraviolet light and convert it to visible light, thus making the carpet appear cleaner and brighter than it really is, for a while. It will eventually give the carpet a yellow cast and the yellow cannot be removed.

Two primary types of machines are used for this process:

  • Cylindrical Foam
  • Rotary Shampoo

The Cylindrical Foam Shampoo machine uses an air compressor to create dry foam before the foam is applied to the carpet and the carpet is then agitated with a revolving cylindrical brush which combs the foam through carpet pile. This method will leave dirt trapped in the carpet pile. Carpet must be thoroughly vacuumed before and after cleaning.

The Rotary Shampoo method uses an ordinary rotary floor machine (the same kind used for stripping wax), sprays shampoo onto the carpet from a dispensing tank and a rotary brush whips the detergent to a foam. Most carpet mills and carpet fiber producers discourage the use of rotary brushes on carpet because of the potential damage that can occur. Overwetting is common with this method which can cause jute straining, shrinkage and odor.

Shampoo methods are inferior due to poor cleaning plus resoiling problems. The Rotary Shampoo method can damage the carpet, especially cut pile (which is what most residential carpet is).

2. Carpet Absorbent Cleaners – dry cleaning

This method is often called “dry cleaning” since virtually no water is used.

In this method, dry absorbent compound (containing small amounts of water, detergent, and solvent,) is sprinkled over carpet or worked into the carpet with a machine. This purpose of this cleaner is to attract and absorb soil. Mechanical agitation from a brush works the cleaner through the carpet.

These products usually contain an absorbent carrier, water, detergent and solvent. The theory is that the liquids dissolve the soil and this soil/detergent/solvent mixture is absorbed into the carrier and is then vacuumed up. They are often used with a detergent prespray in heavily soiled areas.

The absorbent cleaner most commonly is organic, but may also be polymers. The compound is supposed to absorb the dislodged soil and is then vacuumed away. Carpet must be thoroughly vacuumed before and after cleaning.

Very thorough vacuuming should be used to ensure that most of the carrier comes out of the carpet. With the extremely fine powder types, indoor air quality can be reduced. If a white powder starts appearing on shoes and cuffs of pants, too much was used and it was not thoroughly vacuumed up. A common problem is for this white powder to reappear after wet extraction cleaning.

This cleaning method has the advantage of no drying time for interim maintenance, since little water is used. This makes it a common maintenance cleaner.

Host®, Capture®, Love My Carpet®, Arm and Hammer® and Carpet Fresh® would be included in this category.
Bonnet Method / “Carbonated Cleaning”

This method is sometimes called “dry cleaning”, which is a misnomer, since water is used.

Bonnet Shampooing is simply an adaptation of hard floor spray buffing to carpets.

This method for carpet maintenance consists of the use of a rotary or oscillating brush adapted with a stiff brush or drive block designed to drive wet, damp or dry pads. The carpet can be sprayed with the cleaning solution and/or the pads can be soaked in the cleaning solution and squeezed lightly before placing the pad under the driving brush.

The maintenance brochure published by the world’s largest carpet manufacturer, Shaw Industries, suggests not using this method, especially on cut pile, due to pile distortion and fiber damage. This method has very limited capability for soil removal and leaves much of the detergent in the pile since it employs no real extraction. As a result, rapid re-soiling often occurs. Another disadvantage is that the spinning bonnet may distort the fibers of cut pile carpet, fuzzing the pile and leaving distinct swirl marks.

Sometimes, carbonated water is used to (in theory) give better soil suspension and bring down the pH. Companies using this method frequently use “scare” tactics to convince consumers that extraction cleaning or steam cleaning will destroy the carpet.

Check with your carpet manufacturer because many leading carpet mills recommend against this method of cleaning.

3. Hot water extraction or warm water extraction or steam cleaning (“External Extraction”

Hot water extraction or warm water extraction or steam cleaning (“External Extraction”®) is THE BEST WAY TO CLEAN CARPET according to nearly all carpet manufacturers

This method, the best way to clean carpet, is the cleaning method nearly all carpet manufacturers and carpet fiber producers recommend.

This is the only cleaning method classified as “deep cleaning”. All the others are considered “light surface cleaning” or “interim cleaning” because they are incapable of removing soil deep in the pile. Also, all other methods leave large amounts of cleaning agent in the carpet after cleaning.

The maintenance brochure published by the world’s largest carpet manufacturer, Shaw Industries, recommends this method, because its own research indicates that it provides the best capability for cleaning carpet and rugs.

This carpet cleaning method is frequently called steam cleaning due to the fine spray of water used to force dirt out of the carpet which is sucked up by the vacuum slot immediately in front of the spray. Seldom is real live steam used, however. This process consists of spraying a solution of water and detergent into the carpet pile and recovering the water and soil with a powerful vacuum into a holding tank. This can be done from a truck-mounted unit outside the home with only the hose and floor tool brought inside, or by a portable, system brought into the home or office.

From a health standpoint, the truck-mounted system is preferred because the dirty air and humidity are exhausted outside rather than recirculated around the house. Additionally, truck-mounted systems usually are more powerful than portable units and do a much better cleaning job and get the carpet dry more quickly.

With some truck-mounted systems (called PTO’s), the vehicle itself must run in neutral during the cleaning and in many others a separate engine (sometimes with a propane or oil-fired heater) is used to power the unit and heat the water. In both cases, the van MUST be parked well away from the house and positioned so that exhaust fumes do not enter the house. Electric carpet cleaning machines, such as the Bane-Clene systems, do not have this problem.

Depending upon the equipment, temperatures may range from cold tap water to boiling hot water and even super heated water over 200 degrees F. Of course, with extremely high temperatures, there are dangers of scalding should a solution line break as well as the danger of damaging the carpet fibers.

General Comments

The choice of the the best carpet cleaning method is extremely important. Some systems leave residues which promote re-soiling and defeat the whole purpose of cleaning. Some methods actually damage the carpet fibers and shorten the life of the carpet. Check with the carpet manufacturer for recommendations.

Carpet Cleaning Frequency:

If carpet is cleaned before it becomes too unsightly, the cleaning chore will be easier and more successful. Allowing the carpet to become overly soiled may result in irreversible damage. It is a common myth that cleaning the carpet before it is absolutely necessary will cause it to get dirty faster. This goes back to the days when the shampoo methods were the most common.

Carpet in a typical household should be professionally cleaned every 12 to 18 months depending upon the number of residents, amount and type of activity and whether the carpet is light or dark color.

Professional Carpet Cleaning versus “Do-It-Yourself” Cleaning:

The maintenance brochure published by the world’s largest carpet manufacturer, Shaw Industries, recommends professional carpet cleaning over “Do-It-Yourself” because of the potential problems that can occur from using rental equipment – such as yellowing, overwetting, fiber tip damage, severe resoiling, overuse of detergents, etc. Most rental units available do not adequately clean and may actually damage the carpet.


Benefits of outsourcing cleaning companies

Sanitation Services In today’s world, there are days when there are many benefits to outsource the sanitation companies to clean up your work. We are working in a competitive society, and the face of the company where you work is the first impression for customers. A perfectly clean, a clean environment will immediately create an impression of a company professional, organized and successful ..
1. Clean with a high standard anytime, anywhere

An industrial cleaning company will help you achieve a high standard of hygiene wherever you are. Cleaning staff need to be scrutinized, training and evaluation, and management will be responsible to ensure you are happy with the results. Hygiene outsourcing company to help you no longer have to worry about their responsibility for cleaning staff as well.

You no longer have to deal with personnel problems, or headaches when they break holidays and sick days. If the housekeeping staff at work that day you leave the company to outsource your cleaning will provide a replacement immediately.

Sanitation services will be flexible, provide detergent at times suitable to your needs. Similarly, any concerns about the standards will be addressed as a matter of urgency. All this helps you escape the responsibility for dealing with cleaning staff, hygiene issues frees up your time to focus on core business activities.

office cleaning servicers
Photos: office cleaning services

2. Clean the equipment and chemical standards

Some companies outsource sanitation must also comply with the highest standards of health and safety, ensuring a healthy environment clean great that your employees can work best.

You also are affected, take time for the cost and effort of sourcing and purchasing of equipment and products. But all of this has been provided by your cleaning company.

Better still, a quality cleaning company will be updated with the best and latest equipment, gives you the great benefits of creative supplies without talking any salesman!

birth father‘ve leveled the house down
Photos: equipment and chemical cleaning standards

3. Flexibility in cleanup costs

Each company only has a certain budget for sanitation (budget cuts as strong in difficult economic conditions at present). You talk to companies that provide outsourcing sanitation services to find cost-saving solutions, less expensive.

The company has a lot of sanitation options suit your expenses like providing sanitary hourly employees

In conclusion, companies outsource sanitation brings great value for money, with high standards of hygiene, help you no longer have to worry about sanitation worker, chemicals, tools to help you make the savings goods, time and cost.

services provided housekeeping staff daily gio
Photos: Services provided housekeeping staff daily, hourly

Last but not least, the company best commercial cleaning will be committed to raising environmental awareness and reduce emissions, waste. This means using a sanitation company is committed to using green cleaning products, eco-friendly, you increase information ‘green’ your own, ensure your premises are kept sparkling by system using the most sustainable and renewable products.

If you are interested to outsource cleaning services you can use the services of the Company hygienic sanitation TKT, one of the leading companies in Ho Chi Minh City in the area of daily cleaning, regular. We are anxious to meet, consult and communicate with customers about hygiene solutions.

Company sources toilet

error: Content is protected !!